When your water heater begins to leakage, you have to change it quickly. We’ll show you how to install your own gas water heater in less than a day. Even if you don’t require a new hot water heater now, possibilities are you will within the following couple of years. Hot water heater have a tendency to last 7 to 15 years. If your own is obtaining old, this write-up is likewise for you. Replacing a water heater isn’t hard if you’re handy with fundamental tools as well as have a little experience soldering copper.
Tools Needed
4-in-1 screwdriver
Adjustable wrench
Electric tape
Pipe wrench
Plumbers tape
Shatterproof glass
Soldering torch
Measuring tape
Tube cutter
Voltage tester
Wire stripper/cutter
Materials Required
Discharge pipeline
Fittings
Pipe string compound
Pressure safety valve
Solder
Airing vent pipeline and connectors
Water as well as gas piping
Getting Started Installing Your New Warm Water Tank
We’re changing a gas water heater in our demo. The actions for changing a propane hot water heater are precisely the exact same, as well as those for an electric hot water heater are similar.
Regardless, when you’re intending a hot water heater substitute, play it safe. Call your neighborhood division of examinations and ask if you need a permit. And see to it a plumbing or electric assessor checks your job.
Installation Prices as well as Labor
Plumbing professionals usually charge $45 to $65 a hr and also can usually mount a water heater in a day or in 6-8 hrs.
Many property hot water heater cost $150 to $400 for either gas or electrical, plus $200 to $450 if you have a plumber mount it. Extra expensive gas water heaters with unique venting systems additionally are offered. However they’re harder to set up, and we will not take care of them below.
Hot Water Heater Parts and Malfunction
Flue
Cold water shutoff valve
Draft diverter
Temperature level and stress relief valve
Overflow pipeline
Hot water outlet
Anticorrosion Anode Pole
Dip tube
Elements
Insulation
Drain shutoff
Thermostat or control valve
Heater
Thermocouple
Gas supply valve
When to get a new water heater
Your hot water heater is dead when the storage tank leaks. The indicator that your water heater requires changing is a slow-moving drip below, typically turning up as a trail of corroded water. This indicates that the steel tank has actually rusted with as well as can not be taken care of. Various other symptoms, such as not enough or no hot water, typically signal other water heater repair troubles that you can deal with.
If you detect a drip, plan to replace the hot water heater today. Don’t wait up until the leakage obtains bad.
Brand-new water heaters include setup instructions as well as lots of cautions to see to it you deal with the gas, electric and also other links safely. In this post, we’ll supplement those basics with methods as well as “real life” recommendations from several professional plumbings.
However beware: You’ll be dealing with gas, propane or electrical power, all of which are harmful. If you don’t feel confident, employ a pro to look after the challenging parts. And also have your job inspected when it’s done.
Pipes codes differ by area. Define your intended installation to your regional plumbing examiner, including the types of products you plan to utilize for your brand-new links. Much better to get assistance first so you don’t have to change points later!
Figure A: Gas Hot Water Heater Information And Facts
Water
FAMILY HANDYMAN
To print out this picture, see the Added Details at the end of this post.
Number B: Connections for Steel and Plastic Pipe
FAMILY HANDYMAN
Several homes have galvanized steel or plastic (CPVC) water supply pipes. Galvanized steel pipelines are tough to change. We recommend that you remove the pipelines back to the nearby tee, screw on a plastic-lined galvanized nipple area and also finish the connections with copper as shown in our photo collection.
Due to possible warmth build-up, keep plastic pipe a minimum of 6 in. far from the air vent and container. Make a change from plastic to copper with an unique coupling that’s offered any place CPVC is marketed.
Adaptable copper connectors are simpler to mount than solid copper, particularly when the existing pipes and the container inlets do not line up. However not all local codes allow them. If your own does, take unique treatment not to pinch or kink them. You might obtain a leakage.
Read Next
Just How To Enhance Garden Soil in WinterPlay symbol
Exactly How To Boost Garden Soil in Winter
Just how to Adjust Your Water Heater’s TemperaturePlay icon
How to Adjust Your Water Heater’s Temperature level
Exactly how to Examine Your Hot water heater ElementPlay icon
How to Examine Your Hot Water Heater Element
Sign Up For Our E-newsletter
Full DIY projects like a professional! Sign up for our newsletter!
Email Address
SIGN UP
Task step-by-step (12 )
Step 1
Shut off the gas and water
gas
Switch off the gas to the hot water heater by turning the close-by shutoff valve a quarter turn. When off, the manage must be at an appropriate angle to the pipeline. Turn off the major water also and drain pipes the lines by opening a faucet on the lowest floor.
Step 2
Drain the water in the container
hose
Affix a garden tube to the drainpipe shutoff and also drain pipes the water left in the storage tank. Care: The water will certainly be scalding hot! Disconnect the gas line at the close-by union with a pair of wrenches and loosen the pipe from the gas control valve with a pipe wrench.
Action 3
Cut off the water lines
Unscrew
Loosen the air vent pipe from the air vent hood and also move it sideways. Then reduce the hot and cold water lines with a tube cutter. (Unscrew unions for galvanized pipeline or the nuts on versatile ports if you have them.) Glide the old water heater off the beaten track.
Tip 4
Affix the safety valve
Wrap
Wrap the strings of the new temperature and also stress safety valve with Teflon tape (3 turns). Screw it firmly into the storage tank with a pipe wrench. Affix a copper discharge pipeline (see Fig. A for routing details).
Tip 5
Affix pipe assemblies
Solder
Solder brand-new copper adapters to 6-in. sizes of 3/4-in. copper and screw the assemblies into the hot water outlet and also cold water inlet ports in the top of the tank. Add short, plastic lined nipples to protect against galvanic corrosion, particularly if you have tough water or if they’re called for by neighborhood codes.
Action 6
Connect the water lines
Slide
Move the brand-new water heater into area, recut or prolong the old tubing to fulfill the brand-new, and solder the tubing together utilizing copper slip combinings. If the tubes does not align, counter the lines as required with pairs of 45-degree arm joints.
Action 7
Reattach the vent
Reconnect
Reconnect the air vent. Shove it tightly over the draft hood and also slow with three 3/8-in. No. 6 sheet metal screws. Predrill the holes. The vent should increase at the very least 12 in. vertically prior to turning at the initial arm joint.
Tip 8
Use two wrenches to attach the gas line
pipeline
Reconnect the gas line. Coat the threaded ends with pipe joint substance as well as screw the very first nipple right into the gas valve. Use 2 monkey wrench to prevent worrying the valve. Reassemble the continuing to be nipples, ending up with the union (Photo 2). Then follow these four actions to load the tank: (1) Close the drain valve; (2) turn the water back on at the primary shutoff as well as open up the chilly water shutoff to the water heater (leave it open); (3) switch on a neighboring warm water tap up until water comes out; and also (4) check all the joints and fittings for water leaks.
Tip 9
Look for backdrafting
A lot of water heaters rely upon an all-natural draft to attract burning fumes up the flue. If the draft doesn’t function, those fumes, potentially consisting of dangerous carbon monoxide, will splash out into your home. After completing your installment, check the draft.
Close all exterior windows and doors as well as turn on your bathroom and kitchen exhaust followers. After that open a close-by warm water faucet till you listen to the burner in the water heater ignite. After a min, relocate a cigarette smoking suit around the side of the draft hood (Photo 7) in addition to the heater. The smoke ought to be drawn up the air vent pipe. If the smoke doesn’t attract, the fumes from the burner aren’t venting. Shut off the gas to the hot water heater and also call an accredited plumber to deal with the trouble.
Step 10
Look for leaks
Search for bubbles at links
bubbles
Turn on the gas as well as inspect links for leakages by cleaning a 50-50 blend of dishwashing liquid as well as water over the joints. If the mix bubbles, you have a leakage. Tighten up or reconnect joints that leakage. Clean the joints completely dry when ended up. Call the plumbing inspector to check out your job. Comply with the how-to recommendations that comes with the images to see to it the connections are tight.
These suggestions will certainly make your job go much faster and easier:
Measure the elevation of your old water heater and also get a brand-new one the same elevation so you do not have to transform the length of the water, gas or electric lines.
The drainpipe valve (Photo 2) on old water heaters usually clogs up. If the water drains gradually, be patient. CAUTION: It’s scalding hot! TIP: Turn your hot water heater off two hrs in advance to allow the water to cool down.
Hot water heater weigh about 150 pounds. You’ll require a strong assistant or a dolly when you relocate the old one out and also wheel the new one in. Garbage services usually charge about $25 to take the old one. Innovative Pipes & & Drain
8055 E Thomas Rd Device K101 Scottsdale, AZ 85251
( 602) 892-5634
https://innovativeplumbingdrain.com
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |